Search
Search Results
-
Examination of the chlorophyll content of maize hybrids of different maturity groups at different N fertiliser doses
159-162Views:117Nitrogen fertilisation is a critical point of maize production. Five hybrids of different maturity dates were examined in a field experiment, three treatments (different application dates) and three basic fertiliser doses (0, 60, 120 kg ha-1 N) were used. At the 6-leaf-stage of maize, each fertilisation level of the 2nd and 3rd treatment was given 30 kg N ha-1 fertiliser active ingredient in addition to the basic fertiliser doses with the exception of the control plots and further 30 kg N ha-1 fertiliser was applied at the 12-leaf-stage. The final fertiliser doses were 0, 90 and 150 kg N ha-1 in the second treatment and 0, 120 and 180 kg N ha-1 in the 3rd treatment. The whole amount of the basic fertiliser (ammonium nitrate) was applied in the spring, one month before sowing.
The relative chlorophyll content of the maize leaves was measured, with a Minolta SPAD-502 measurement device. The measurements were carried out at the 6-leaf growth stage (V6) of maize on the youngest fully developed leaf of the 6th, 7th and 8th plants from the second row of each plot.
There were significant differences in the SPAD-readings measured at the V6 phenophase of maize between the hybrids (p<0.001) and the fertiliser treatments (p<0.05). The regression analysis did not show any correlation between the SPAD-values and fertilisation.
The highest significant SPAD-reading and yield were obtained by applying 120 kg ha-1 N. As a result of the regression analysis performed on yield, it can be concluded that the correlation between fertilisation and yield in the 1st and 2nd treatment was moderately close (r=0.439, r=0.480) and it was close in the 3rd treatment (r=0.513). The correlation between the SPAD-readings and yield was the closes in the 2nd treatment (r=0.639), while the SPAD-value had a 40.9% influence on yield (p<0.001).
-
Comparative analysis on the fertiliser responses of Martonvásár maize hybrids in long-term experiments
111-117Views:68The results of experiments carried out in the Agricultural Research Institute of the Hungarian Academy of Sciences clearly show that in the case of hybrids grown in a monoculture greater fertiliser responses can be achieved with increasing rates of N fertiliser than in crop rotations. In the monoculture experiment the parameters investigated reached their maximum values at a rate of 240 kg/ha N fertiliser, with the exception of 1000-kernel mass and starch content. In both cases the starch content was highest in the untreated control, gradually declining as the N rates increased. Among the parameters recorded in the crop rotation, the values of the dry grain yield, the 1000-kernel mass, the protein yield and the starch yield were greatest at the 160 kg/ha N fertiliser rate, exhibiting a decrease at 240 kg/ha. Maximum values for the protein content and SPAD index were recorded at the highest N rate. It is important to note, however, that although the N treatments caused significant differences compared to the untreated control, the differences between the N treatments were not significant.
In the given experimental year the values achieved for the untreated control in the crop rotation could only be achieved in the monoculture experiment at a fertiliser rate of 160 kg/ha N, indicating that N fertiliser rates could be reduced using a satisfactory crop sequence, which could be beneficial from the point of view of environmental pollution, crop protection and cost reduction.
The weather in 2006 was favourable for maize production, allowing comparative analysis to be made of the genetically determined traits of the hybrids. Among the three hybrids grown in the monoculture experiment, Maraton produced the best yield, giving maximum values of the parameters tested at a fertiliser rate of 240 kg/ha N. The poorest results were recorded for Mv 277, which could be attributed to the fact that the hybrid belongs to the FAO 200 maturity group, while the other hybrids had higher FAO numbers. Maraton also gave the highest yields in the crop rotation experiment at the 160 kg/ha N level. All three hybrids were found to make excellent use of the natural nutrient content of the soil.
It was proved that the protein content of maize hybrids can only be slightly improved by N fertilisation, as this trait is genetically coded, while the starch content depends to the greatest extent on the ecological factors experienced during the growing season. -
Correlation analysis of relative chlorophyll content and yield of maize hybrids of different genotypes
211-214Views:103In 2021, correlation between relative chlorophyll content and yield in three maize hybrids of different genotypes was examined. The data were collected at the Látókép Experimental Station of the University of Debrecen located on the Hajdúság loess ridge in Hungary. The soil of the small plot field strip plot trial, which was set up in 2011, was calcareous chernozem. Apart from the control treatment (without fertilisation), N fertiliser is applied in the form of base and top dressing. The base fertiliser containing 60 and 120 kg ha-1 N of nutrient applied in spring was followed by top dressing containing +30–30 kg ha-1 N in V6 and V12 phenophases. SPAD values measured at different phenological stages of the growing season increased by an average of about 28% up to 10 leaf stage for all three hybrids. In the pre-silking period (Vn), the relative chlorophyll content decreased by 8% on average. After an average increase of 14% in the tasselling and silking period, SPAD decreased by an average of about 29% at full maturity (R6).
For the different fertiliser treatments, higher N doses resulted in higher yields. In the basal fertiliser treatment, the A 60 N dose resulted in an average 34% increase in yield, and the A 120 N dose resulted in an average 94% increase in yield compared to the control. The 60 kg ha-1 N basal fertiliser (A60) increased in the V6 phenophase with an additional 30 kg ha-1 N resulted in an average yield increase of 26%. When 120 kg ha-1 N of basal fertiliser (A120) was increased by an additional 30 kg ha-1 N in the V6 phenophase, only the Merida hybrid showed a significant yield increase (7%). No further yield increase was observed when V690 and V6150 treatments were increased by an additional 30 kg ha-1 N in the V12 phenophase. The yield of the Armagnac hybrid decreased by almost 20%, the yield of Fornad by 3% and the yield of Merida by 1%.
-
Comparative examination of a bacterium preparation (BACTOFIL® A10) and an artificial fertilizer [CA(NO3)2] on calcareous chernozem soil
75-80Views:109In a small-pot experiment a bacterium preparation, Bactofil® A10 and an artificial fertilizer containing Ca(NO3)2 in different dosages were studied on calcareous chernozem soil, concerning the readily available nutrient content of soil (nitrate-nitrogen, AL-phosphorus, ALpotassium content of soil, some soil microbial characteristics (total number of bacteria and fungi, cellulose-decomposing and nitrifying bacteria, CO2-production of soil), and the amount of the plant biomass.
The readily available nutrient content of the calcareous chernozem soil increased due to the treatments, except for the change in the soil nitrate-nitrogen content, which did not measure up to the control due to the effect of high-dosage Bactofil.
The treatments also influenced the examined microbial characteristics of the soil positively. The artificial treatments significantly increased the total number of bacteria and the number of cellulose-decomposing and nitrifying bacteria. The low-dosage Bactofil significantly increased the number of cellulose-decomposing bacteria and both Bactofil dosage significantly increased the number of nitrifying bacteria. The measure of the soil respiration grew in all treatments, but significantly only in Ca(NO3)2 fertiliser treatments.
The quantity of the plant biomass was grew in a low-dosage Bactofil and significantly in the artificial fertiliser treatments. The highest plant biomass quantity was measured in the high-dosage artificial fertiliser treatment.
In the correlation analyses we found some medium positive correlation between the soil chemical, microbiological parameters examined, and the plant biomass in the case of both treatment-forms.
Based on our results Ca(NO3)2 artificial fertiliser treatments on calcareous chernozem soil proved to be more stimulating regarding the
examined soil characteristics and the amount of the plant biomass, but the low-dosage Bactofil also positively influenced the majority of the
soil characteristics examined in terms of nutrient supply. -
Examinations of the carbon dioxide emission of the soil in the case of different tillage methods in a field experiment
209-212Views:206Today's global challenge is the increasing concentration of carbon dioxide (CO2) and other greenhouse gases in the air. The level of CO2 emissions may be significantly affected by the agriculture and, more specifically, the applied tillage method, even though to a lesser extent than industrial production. On a global scale, the CO2 emission of an agricultural area is insignificant in comparison to that of a large-scale plant in an area of the same size, but areas under cultivation, including arable land, have a large global area. In this paper, we investigated the relationship between applied soil tillage methods and carbon dioxide emissions in the case of different fertiliser treatments. In our experiment we examined four types of tillage with five different fertiliser effects. Comparing fertiliser treatments and tillage methods, it was found that their interaction significantly affected carbon dioxide emissions, the lowest value was obtained in the case of the 210 l ha-1 Nitrosol+N-LOCK – tillage radish treatment. Strip and tillage radish methods have relatively homogeneous, low value. -
Basic Research for the Development of Fertiliser Spreaders
52-57Views:79The knowledge of the physical characteristics of fertiliser particles is essential for the constructors and operators of fertiliser distributors. Among physical characteristics, the most important are the frictional and aerodynamic properties for the description of particle movement. Adjustable angled slopes, shearing boxes and various rotating disks are used to identify frictional properties. We have developed a high precision shearing box with digital force measuring cells and a distance signaller (incremental transducer) that we use for slide tests efficiently. We measured the frictional characteristics of 6 different fertilisers: the inner coefficient of friction and the coefficient of friction on ten test surfaces most commonly used in machinery, and we specified the relationship between displacement, loading and the coefficient of friction. We can conclude that the material of the frictional surface significantly influences the force of friction.
However, our experience tells us that the shearing box is not suitable for the measurement of the inner friction, since the examined particles slide on the metal surface of the shearing box in a growing extent in the course of displacement, so it does not measure the real inner friction. Therefore, in our experiment we have developed rotating shearing equipment with a constant shearing surface to identify the inner friction. We tested the equipment with fertilisers and we identified the inner frictional characteristics of 6 different fertilisers. With the developed rotating shearing apparatus we could measure the real inner friction of the particles.
To identify the aerodynamic characteristics of granules, wind tunnels and free-fall tests are used. An elutriator have been developed for our investigation. We have used fertilisers for testing the measuring equipment and we have identified the aerodynamic characteristics of 6 different fertilisers. -
Effect of N, P and K fertilisers and their interactions in a long-term experiment on winter barley (Hordeum vulgare L.)
87-92Views:165The aim of this work was to analyse the effect of K, P and N supplies on the yield of winter barley in a long-term mineral fertilisation experiment with clearly distinct soil nutrient supply levels in order to develop fertilisation guidelines for winter barley growers. The experiment was set up in 1989 on a chernozem meadow soil calcareous in the deeper layers, applying all possible combinations of 4 levels each of N, P and K fertiliser, giving a total of 64 treatments.
The results of analyses performed in 2011 and 2012 can be summarised as follows:
- In 2011, when rainfall supplies were deficient in the shooting phase, improved K supplies (324 mg kg-1 AL-K2O) increased the grain yield, but in 2012, when rainfall supplies were more evenly distributed, K supply levels in the range 210–335 mg kg-1 AL-K2O had no significant influence on the yield of winter barley.
- An analysis of the P treatments revealed that, compared to the 119–133 mg kg-1 AL-P2O5 level (P0), better P supplies (186–251 mg kg-1) led to a significant increase in the grain yield.
- In both years rising N rates significantly increased the yield up to an annual N rate of 160 kg ha-1.
4. A K×N interaction could only be detected in the nutrient supplies of winter barley in 2011. The yield-increasing effect of N fertiliser was more pronounced at better K supply levels, while K fertiliser led to higher yields in the case of better N supplies.
-
The impact of climatic factors on the relative chlorophyll content and yield of a maize hybrid in a long-term experiment
71-77Views:193The impact of the climatic factors of crop year on the relative chlorophyll content of maize was examined for three years. The examinations were carried out on the Látókép Experiment Site of the University of Debrecen on calcareous chernozem soil in a small-plot, non-irrigated long-term field experiment with strip plot design. In addition to a non-fertilised (control) treatment, nitrogen (N) fertiliser doses were applied as base and top dressing. The 60 and 120 kg N ha-1 base dressing doses were followed by two top dressing doses at the V6 and V12 phenophases.
Averaged over the different fertiliser treatments, SPAD readings increased in all three years as the growing season progressed. The highes SPAD value increase was observed in the average crop year (2017) at the V12 phenophase (11.8), which further increased at the R1 phenophas, by 3,7. No significant Spad value difference was observed between the average (2017) and the dry year (2018) at the V6 growth phase. However, in the wet crop year (2016), the V690 treatment provided the statistically highest relative chlorophyll content (46.8). At the V12 phenophase, the base dressing dose of 120 kg N ha-1+30 kg N ha-1 (V6150) showed to be successful in two years (2016 and 2018), while in 2017, the base dressing dose of A60 was successful. The impact of crop year on relative chlorophyll content can be clearly shown at the R1 growth stage. In all three years, the significantly highest relative chlorophyll content could be achieved at different nutrient levels: A60 in 2016, V6150 in 2017 and V690.
In a wet year (2016), higher yield could be achieved as a result of the 60 kg N ha-1 base dressing and 30 kg N ha-1 at the V6 growth stage (V690) as top dressing in comparison with 2017 and 2018, when higher fertiliser dose (120 kg N ha-1 base dressing and 30 kg N ha-1top dressing at the V6 growth stage) was needed to achieve a significant yield surplus.
Altogether, averaged over the different treatments, the highest yield (12.48 t ha-1) was observed in the wet year, when the relative chlorophyll content was also the highest (50.6).
-
Land use, water management
81-87Views:200Due to the prognosed population increase to 9.2 billion people by 2050, the world’s crop production does not have any other chance than to increase production. This demand is a huge challenge for agriculture. Based on the forecasts, the growth rate of production of the main cereals will decrease as a result of the effect of soil, water, the increasing fuel and fertiliser prices and the impacts of climate change. Methods ensuring sustainability have to be preferred. Precision agriculture is the most effective method of crop production. We have to apply minimum cultivation in order to protect the soil surface, maintain its moisture content and increase its water reception ability. In addition to the localised use of fertiliser, sowing seed, irrigation and pesticides, it is also important to apply them in a targeted way on the basis of plot imaging. The use of the new technology results in significant cost saving and it could also reduce environmental load.
-
Comparative examination of a mineral fertiliser and a bacterial fertilizer on humic sandy soil
111-116Views:79In our pot experiment, the impact of a bacterial fertilizer, Bactofil® A10 and a mineral fertilizer Ca(NO3)2 applied in different rates was studied on some soil chemical and microbiological characteristics of a humic sandy soil (Pallag). Perennial rye-grass (Lolium perenne L.) was used as a test-plant. Samples were collected four and eight weeks after sowing in each year. The experiment was set up in 2007-2009 in the greenhouse of
the UD CASE Department of Agrochemistry and Soil Science. The available (AL-extractable) nutrient contents of soil, among the microbial parameters the total number of bacteria, the number of microscopic fungi, cellulose-decomposing and nitrifying bacteria, the sacharase and urease enzyme activity, as well as the soil respiration rate were measured.
Statistical analyses were made by means of the measurements deviation, LSD values at the P=0.05 level and correlation coefficients were calculated. Results of our experiment were summarised as follows:
− The readily available nutrient content of humic sandy soil increased as affected by the treatments, in case of the available (AL-extractable) phosphorus and potassium content the higher value was measured in high-dosage artificial fertilizer treatment.
− The treatments had also positive effect on several soil microbial parameters studied. The higher-dosage mineral fertilizer treatments had a beneficial effect on the total number of bacteria, cellulose-decomposing and nitrifying bacteria. No significant differences were obtained between the effect of treatment in case of the total-number of bacteria, the number of microscopic fungi and nitrifying bacteria.
− On the sacharase enzyme activity the artificial fertiliser treatments proved to be unambiguously stimulating, the urease activity significantly increased on the effect of the lower-dosage Ca(NO3)2 artificial fertilizer treatment.
− The soil respiration increased in all treatments in related to the amounts applied, significantly increased in the highest rate of Ca(NO3)2 fertilizer addition.
− Some medium and tight positive correlations were observed between the soil chemical and microbiological parameters studied in case of both nutrient sources.
Summarizing our results, it was established that the organic and all the mineral fertilizer treatments had beneficial effects on the major soil characteristics from the aspect of nutrient supply. In majority of the examined soil parameters (AL-extractable phosphorus- and potassium, total number of bacteria, number of cellulose-decomposing and nitrifying bacteria, activity of sacharase enzyme) the high rate of Ca(NO3)2 mineral fertilizer treatment proved to be more stimulating, but at the same time the high rate bacterium fertilizer resulted in significant increases in
the nitrate-N content, the AL-potassium content of soil, the total number of bacteria, the number of cellulose-decomposing and nitrifying bacteria and the urease enyme activity.
Our examinations showed that the mineral fertilizer treatments proved to be more stimulating on most of the soil parameters studied but according to our results, it was established that Bactofil is efficiently applicable in the maintenance of soil fertility and the combined application of
mineral fertilizer and bacterium fertilizer may be a favourable opportunity – also in aspect of the environmental protection – in maintaining soil fertility. -
Changes in the Macro-, Mezo-, and Microelement Contents of Maize Hybrids in Relation to the Level of Nutrient Supply
126-130Views:63n my research, I measured the effect of NPK fertilisation on the macro- meso- and microelements content of maize hybrids in 2001. The experiment was set in the demonstration garden of the Department of Crop Production and Applied Ecology in the Agricultural Centre, at the University in Debrecen. The soil of the experiment is calcerous chernozem soil. Five fertilisation steps were applied. Besides the control the smallest rate was 40 kg N; 25 kg P2O5; 30 kg K2O of active ingredients. The largest rate was five times more than the smallest one: 200 kg N; 125 kg P2O5; 150 kg K2O, which is equal to 475 kg mixed active ingredients. The NPK treatment significantly influenced the macrolement content in several cases. The N content was the lowest in the control treatment. Compared to this the fertiliser treatments significantly increased the N content of hybrids. However the highest amounts of potassium and phosphorus could be measured in the control and the lowest amounts could be measured at the N 200+PK kg/ha treatment.
The Ca content of hybrids was the highest in the N 120+PK kg/ha treatment, while their Mg and Zn content was the highest in the control treatment. The lowest amounts were weighed in the N 200+PK kg/ha treatments, that in several cases resulted in statistically proved decreasement compared to the control or the lower fertilizer doses. Considering the two mesoelements and Zn the most favourable results were obtained in the case of the Norma SC and DK 366 SC hybrids.
Summing up what has been said moderate amounts of fertiliser doses (N 40-120+PK kg/ha) had a favourable influence on the micro- and macroelement content of hybrids. -
Effects of production factors on the yield and yield component of winter wheat
26-31Views:76The effect of major production factors (forecrop, fertilisation, irrigation, soil cultivation and soil preparation) on the yield components and yield of winter wheat were studied in a long-term experiment set up at the Látókép Experimental Nursery of the Agricultural Sciences Centre of the University of Debrecen. The results of regression analysis led to the following conclusions:
• In our experiments in 2000, after using maize as a forecrop –based on the results of analysis of regression – fertilisation determined the yield.
• After using pea as a forecrop, a N50 P35 K40 kg/ha fertiliser rate led to an economical increase in the yield of winter wheat.
• None of the determinative yield components varied significantly for winter wheat produced after using pea as a forecrop.
• There is a closed, significant correlation between plant height, spike length, plant and spike mass, the number of spikelets and grains per spike after using maize as forecrop. The thousand grain mass is different from the other yield components, because it is not part of the relation system of
those yield components.
• The increased yield of winter wheat after maize has been used as a forecrop is due to the positive change in grain number per spike yield component. -
Using research findings in precision maize production
227-231Views:195The effect of crop production factors on maize yield are examined on chernozem soil in a more than 30 year old long-term experiment on the Látókép Experiment Site of the Centre for Agricultural and Applied Economic Sciences of the University of Debrecen. The aim of research is to evaluate the effect of fertilisation, cultivation, plant number, genorype and irrigation. The analysis of the data in the database of the examined period makes it possible to evaluate the effect of maize yield, as well as that of the crop production factors and the crop year, while the correlations and interactions between these factors were also examined. During the examination of the cultivation treatments, it was concluded that the highest yield was obtained as a result of autumn ploughing, but its effect largely differs in the irrigated and the nonirrigated treatments. Based on our examinations, strip cultivation should be applied periodically (e.g. strip – strip – ploughing – loosening) in areas with favourable soil conditions free from compacted layers.
In years with smaller, average precipitation supply or when the precipitation was higher than average, higher plant numbers were more favourable. Under drier conditions, but especially in several consecutively dry years, a lower plant number can be recommended which is not higher than 60 thousand per hectare. In the case of favourable water supply, 70-80 thousand plants per hectare can be used. The yield increasing effect of fertilisation was significant in the case of both non-irrigated and irrigated conditions, but it was much more moderate in the non-irrigated treatment. The extent of weed coverage was significantly affected by the previous crop. In the case of a favourable previous crop (wheat), the weed coverage was significantly lower than after an unfavourable previous crop (maize). In the case of the same previous crop (maize), the extent of weed coverage was mostly determined by the crop year and the extent of precipitation supply. Irrigation is not enough in itself, because if it was not accompanied by intensive nutrient management, yields started to decline.
The results of researhc, development and innovation contributed to the technological method which makes it possible to apply locally adjusted sowing seed, fertiliser and pesticide in a differentiated way, as well as to change the method of operations within the given plot. -
Preliminary Critical P-limit Values of 0.01 M CaCl2 Soil Test Procedure
18-21Views:103In the last decade, the 0.01 M CaCl2 extraction procedure was tested as a multi-nutrient extractant. In 1995-97, international joint research activities were carried out within the COPERNICUS project. Detailed calibration of conventional and the 0.01 M CaCl2 extraction procedures for pH, Mg and K were published.
The amount of phosphorus extracted using a 0.01 M CaCl2 solution is very low and reflects the intensity parameter of phosphorus bio-availability. As a readily desorbed P fraction of soils can reflect the soil P-supply and the CaCl2-P values are in close correlation with P-fertiliser rates and P balance. However, the effects of various soil characteristics on CaCl2-P values are different and their interpretation is difficult.
Relatively poor correlations were found between amounts of P extracted by conventional and CaCl2 soil test methods and, therefore, P limit values could not be calculated directly. To characterise the soil P supply at different sites, the CaCl2 desorbed P and the adsorbed P in a modified Baker Soil Test were also applied.
Soil test results of Hungarian long-term fertiliser experiments and recommended CaCl2-P limit values, calculated on yield effects and soil characteristics, are discussed. -
Application of the Collision Cell (CCT) in the ICP-MS Analytical System
120-125Views:130Our laboratory has seen a sharp rise in the number of requests for the analysis of smaller and smaller concentrations of elements from foods, plants, soil, organic fertiliser, irrigation and ground water, sewage, sewage sludge, raw material of food, as well as human and animal origin samples. From the above elements the inductively coupled plasma mass spectrometer is capable of analysing the smallest concentration of elements. Our method of analysis is to use our ICP-MS instrument, together with a ICP-MS with Collision Cell Technology (CCT). The CCT method has better detection limit, with 1-3 magnitudes, compared to the normal ICP-MS analytical method. The CCT has better detection limits mainly for the following elements in the periodical system: analysis of arsenic, selenium, germanium, vanadium and chromium. Additionally a collision cell can be applied for the analysis of silicium, sulphur, zink, copper, iron, calcium, magnesium and potassium in smaller concentrations.
-
Movement of Particles in the Air
22-26Views:101The physical characteristics of particles (seeds and fertilisers) can strongly influence their movements both in seeding and spreading machines and in the air. It is therefore essential to study these particles when constructing such machines. In this respect the size, shape, coefficient of friction and aerodynamic resistance of particles are of great importance.
Due to their irregular shape, determining the size of particles is a troublesome process. A precise description of particles has to include several sizes and can be obtained from their screen size. Many physical properties of particles are relevant during movement in the air, but the aerodynamic resistance coefficient is the most important (Hofstee et al., 1990). Two types of wheat and four types of fertiliser particles were investigated (supported by the National Scientific Foundation OTKA, T-026482). An elutriator was designed and constructed (Csizmazia et al., 2000), in which an airflow is supplied by a centrifugal fan. Air velocity was measured with a thermal sensor. Particle sizes, mass and terminal air velocity were measured. The influence of the aerodynamic resistance coefficient on the particles’ motion is also discussed. -
The impacts of spring basal and side dressing on maize yield
83-86Views:172The yield potential of maize is very high. According to Tollenaar (1983), maize yield potential is as high as 25 t ha-1 (absolute dry yield) which is the highest among all cereals. In order to fully utilise this high yield potential, proper nutrient replenishment is of chief importance among all agrotechnical factors.
The aim of research was to examine the effect of nitrogen fertiliser applied as basal and side dressing on maize yield.
The measurements were performed at the Látókép experiment site (47° 33’ N, 21° 26’ E, 111 m asl) of the Centre for Agricultural Sciences of the University of Debrecen on mid-heavy calcareous chernozem soil with deep humus layer in an established experiment in 2011, 2012 and 2013. The trial design was split-split-plot with two replications.
Based on the experiment results, it can be established that the nutrient uptake of maize is greatly dependent on the amount of water store in the soil. From the aspect of the development of the maize plant and water supply, the most determinant factor was the distribution of precipitation over the growing season and not the amount precipitation. This is shown by the fact there was only 276 mm precipitation – which was favourably distributed – in 2012 to increase the availability of nutrients and the main average was the highest in this year (14.394 t ha-1).
Spring basal dressing helped maize development in all three years even on chernozem soil which is well supplied with nutrients. Although the effect of side dressing did not result in any yield increase, it could still contribute to mitigating the stress effects caused by environmental factors. Altogether, nutrient supply adapted to the various development stages of maize can favourably affect the success of maize production.
-
Approximate Model for Examination of Cone Dispenser Eccentricity
47-49Views:70The most important distributing construction of small plot seed-drills, fertiliser dispensers is the cone dispenser. The cone dispenser can operate based on simple gravity or with Oyjord-type cone-cell or Hege-type cone-belt structure. The unevenness of spreading of each type is significantly influenced by the feeding roll above the cone and the misalignment of the cone dispenser. On designing, preparing and setting I realised that this job could be done much faster and more precisely if there would be model for testing the misalignment of the cone dispenser. In my article I will provide information about the essence of the mathematical model and its derivations. For the calculations I prepared a chart program in Microsoft Excel.
In order to test the computed model I made experimental examinations. I put together a test bench for the measurements. I revealed that the mathematical model describes the unevenness of spreading caused by misalignment. In addition, I discovered that even a misalignment of 0.25-0.5 mm can be pointed out by measurements and is in proportion to the variety factor determined theoretically. -
Comparison of the physiological responses of an oil-pumpkin cultivar and hybrid under different nitrogen supply conditions
65-69Views:177Cucurbita pepo var. styriaca is known as a medicinal crop among other cucurbits. The benefits of cucurbits fruits are very important in terms of human health, purification of blood, removal of constipation, digestion and supplying energy. The mutant styrian oil-pumpkin (Cucurbita pepo L. convar. Pepo var. styriaca Greb.) exposes a complete lack of lignification of the seed testa. For this reason, this kind of naked pumpkin seed is more consumable as snack than other seeds. The vegetative growth of plants is crucial for fruit production. Nitrogen is the most imperative element for the proper vegetative growth and development of plants which significantly increases and enhances yield and its quality by playing a vital role in the biochemical and physiological functions of plants.
Field studies were conducted to study the effect of nitrogen nutrition on certain physiological parameters and their differences between the styrian oil pumpkin hybrid and cultivar (Gleisdorfi Classic cultivar and GL Rustical hybrid). The small block experiment was carried out based on a factorial experiment with a completely randomised block design and four replications in the Research Institute of Nyíregyháza during the summer period of 2017 and 2018. Three different concentrations of nitrogen fertiliser was applied at sowing. Photosynthetic pigments (chlorophyll-a, -b and carotenoids) were analysed as one of the basic factor of efficient photosynthesis. The yields of two genotypes were also measured in all treatments as seed-weight. The contents of photosynthetic pigments were higher in the oil-pumpkin hybrid, mainly the carotenoids in 2018. The vegetation period of 2018 was drier than in 2017, the hybrid oil-pupmkin was more efficient in stress tolerance than the cultivar with higher carotenoids pool. The obtained yield was more pronounced in the oil-pumpkin hybrid than the cultivar in all examined years. The hybrid GL Rustical was more sensitive to nitrogen treatment than the cultivar Gleisdorfi Classic.
-
Changes in the Sulphur Content of Winter Wheat in a Field Experiment
85-88Views:75The use of superphosphate as P-containing fertiliser decreased in the last years in many countries in accordance with strict air pollution laws, and the S-deposition decreased from the atmosphere to the soil as well.
Winter wheat is the one of the S-demanding plants. Recently, the gradually increasing S absence endanger the formation of required average yield of winter wheat, and has bad effect on its quality.
We examined the effect of treatments on the sulphur-, nitrogen content and the N/S ratio of winter wheat in the whole upperground plant and in the grain and straw at harvest in a arable land sulphur fertilization experiment on brown forest soil (Agricultural Company of Felsőzsolca).
We analysed the samples from spring to harvesting, in the critical phenophases. In this study we discuss only the values from the stooling and stalking and the results of analysis of grain and straw in the harvest.
We experienced that the concentration of sulphur in the whole upperground parts of winter wheat showed increase to the end of vegetation independently of fertilization. The N/S ratio was between 8% and 12% in the beginning of the growth period in the whole upperground plant, while the ratio in the grain at harvest was between 13 and 14%. When we examined the whole upperground plant, stalk and leaf at stalking, we got the highest sulphur content in the leaf. Mostly the middle level sulphur fertilization dose (4 l/ha) increased the sulphur accumulation in the green plant. At total maturing, the greatest part of accumulated sulphur is in the grain, but then the effect of fertilization is less glaring. -
Influence of nitrogen fertilisation on the technological quality of wheat
47-55Views:47Wheat is one of the most grown crops around the world. Its primary use is in the production of bread, bakery, and confectionery. The provision of essential nutrients, mainly nitrogen, plays a pivotal role in the growth and development of wheat. The wheat varieties used in the experiment are Alfold and Mv. Menrot. The rates of nitrogen used in the experiment are: 0, 200, 400, 600, 800, and 1000 kg N ha-1. The aim of this study is to evaluate the effect of nitrogen fertilisation on technological quality of wheat and to find the appropriate fertiliser rate to reduce pollution. The results indicate that nitrogen fertilisation did not show a significant effect on thousand kernel weight and test weight. However, nitrogen fertilisation significantly affected protein content, gluten content, Zeleny sedimentation index, and the falling number. The higher the nitrogen fertilisation the better the technological quality parameters of the wheat. The protein content, gluten content, Zeleny sedimentation index and the falling number were the lowest at 0 kg N ha-1 followed by 200 kg N ha-1 then 400 kg N ha-1 and the highest at 600 kg N ha-1.
-
Examination of the angle position on the cone dispenser
204-207Views:75The most important distributing construction of small plot seed-drills and fertiliser dispensers is the cone dispenser. The cone dispenser can operate based on simple gravity or with an Oyjord-type cone-cell or Hege-type cone-belt structure. The unevenness of spreading of each type is significantly influenced by the aberration of the vertical angle position of the cone dispenser. An approximate method was improved modelling of the fault of the cone dispenser. In my article, I will provide information about the essence of the model and its derivations.
On the model, I cover the cone piston with a theoretical net and at random scale between each scale interval I count the forces acting on the grain and the movement of the grain. If I set the scale of the net close enough, with good proximity, I get the whole orbit. The unevenness of dispensing can be calculated from the position of the grains getting to the bottom of the cone in case of different geometric data. My measurements imply that an approximate method is able to model both the tendency and the value of the deviation caused by the fault of the angle position. Both the theoretical model and the measurement prove that 2-3° deviation results in significant change in the unevenness of dispensing. -
Evaluation of the interaction between environmental factors, cultivation and fertilisation
103-108Views:96The effect of production factors on maize yield was examined in the Látókép Experiment Site of the Centre of Agricultural and Applied Economic Sciences of the University of Debrecen on calcareous chernozem soil between 2001 and 2003. The impact of environmental factors (precipitation, temperature, number of sunny hours), cultivation methods (autumn ploughing, spring shallow cultivation) and fertilisation (non-fertilised, 120 kg N + 90 kg P2O5 + 106 kg K2O, and 240 kg N + 180 kg P2O5 + 212 kg K2O) on maize yield was examined. During the three years, autumin ploughing significantly increased yield by 2.91 t ha-1 in comparison with spring shallow cultivation. The yield increasing effect of fertilisation was observed in each year, although its extent depended on the given crop year and the applied cultivation method. The higher fertiliser dose (240 kg N ha-1) did not cause significantly higher yield in either year. After the evaluation of the observed correlations, it can be established that the yield increasing
effect of fertilisation was higher in the case of autumn ploughing in comparison with spring shallow cultivation. The environmental factors (especially the extent of precipitation) significantly affected the maize yield. -
Results of Sulphur Fertilization Experiment with Oilseed Rape
174-178Views:60The rape is definitely a sulphur-demanding crop, which yield and the quality of its oil is threaten by the emerging shortage of sulphur nowadays. We made sulphur fertilising trials on two places in the northeastern rape growing area (in Felsőzsolca and Mezőkövesd), in the season 2001/2002. We compared the result the 5 five treating set in 2 repeats on brown forest soil with the results of the control plots. We used FitoHorm 32 S sulphur solution as sulphur fertiliser, with the dose of 3, 6 and 10 litres per hectare, as well as the joint effects of sulphur and boron; and the effect of boron alone. On the assessment of our results we looked for relation between the sulphur fertilising, the seed production, the oil content and the protein content.
-
Spent mushroom compost (SMC) – retrieved added value product closing loop in agricultural production
185-202Views:911Worldwide edible mushroom production on agro-industrial residues comprises of more than 11 million tons of fresh mushrooms per year. For 1 kg of mushrooms there is 5 kg of spent mushroom compost (SMC). This enormous amount of waste results in disposal problems. However, SMC is a waste product of the mushroom industry, which contains mycelium and high levels of remnant nutrients such as organic substances (N, P, K). The spent mushroom compost is usually intended for utilization, but there are increasing numbers of experiments focusing on its reuse in agricultural and horticultural production. Recently, the increase of the global environmental consciousness and stringent legislation have focused research towards the application of sustainable and circular processes. Innovative and environmentally friendly systems of utilisation of waste streams have increased interest of the scientific community. Circular economy implies that agricultural waste will be the source for retrieving high value-added compounds. The goal of the present work was to carry out a bibliographic review of the different scenarios, regarding the exploitation of this low cost feedstock with huge potential for valorisation.