Search
Search Results
-
The Effect of annealing temperature on corrosion resistance and microstructure of Zr-Sn-Nb-Fe alloy
420-424Views:115The Ti-2Al-2.5Zr titanium alloy plate in beta phase water quench at different times of the reentry after annealing is implemented while primary phase number and size distribution of samples are obtained. This research is carried out on corrosion behavior in 3.5% [mass fraction] NaCl solution. Experimental study showed that after the beta phase water quenching Ti-2Al-2.5Zr titanium alloyed after 500 oC annealing when partial recrystallization happened. There seems to be lots of tiny dispersion in the alloy that was annealed with its samples of six-party [HCP] structure of Ti, Zr, Al phase 2 with the dimension below 100 nm. Reaching 500 oC when the rate of annealing at a primary phase of the sample at 550 oC is low 90% of the primary phase is less than 100 nm. The changing of the rule of present decreasing also triggers little difference overall. Precipitation in the process of annealing Zr [Nb,Fe,Cr] 2is less that proves to be good for corrosion resistance.
-
Economic Analysis of Thermal Insulation Systems
1-5Views:88One of today's most important problem of inadequate energy management. In Hungary, most of the buildings considered to be outdated in the building materials used and taking into account the construction technology. A significant part of the heat energy used for heating purposes before leaving the environment through the building envelope elements used in time. In our study we investigate whether an average house how much energy you can save the facade walls with insulation.
-
What is worth knowing about the establishment from a work safety point of view
24-31Views:114Under establishment, we mean the process that results in the creation of a new unit (eg factory, plant, office, etc.), a workplace or an existing one what will be renewed, expanded or restructured, or installed; installed on a machine, plant, appliance, whether or not for productive or non-productive purposes. It is generally true that the design, construction, use and subsequent operation of workplaces, facilities, technology, materials, energy, personal protective equipment; production, distribution, import, transportation, movement, use and use of workplaces; in the absence of these, the requirements of the scientific-technical standard can be expected. An employer, operator, and service provider must adapt to market conditions. Accordingly, it should monitor the expectations of customers, business partners, market changes, trends to adapt to expectations, and therefore constantly develop their products, services, produce reliable quality, ensure that quality meets the market expectations providing personal and material conditions to ensure that employees can effectively and safely meet market expectations. The recognized business perception of the employer is to accomplish the above, the objectives to be achieved must be formulated, priority should be given to the potential risks (with particular regard to occupational safety risks) to be measured, measures to be taken to ensure effectiveness, short-, medium- and long-term planning, investment.
-
Investigation of SCOR Model in Connection with Performance and Warehouses
227-239Views:145Business leaders can use several strategic tools to improve the organization, depending on what they consider to be important. The Supply Chain Operational Reference Model (SCOR) is one of these. Its importance is to link business processes, performance metrics, best practices, and technology together and to create a unified structure. It promotes communication between the stakeholders of the supply chain and improves supply chain management and the efficiency of the related supply chain improvement activities. The aim of this study is to find out how the SCOR model appears in the international literature related to warehousing and performance. What methods and tools do authors use to investigate their research questions and hypotheses? Description statistics and category selection were used to present the results of the study. The number of SCOR model researches related to warehouse performance measurments are very rare, it is rather used to describe different processes. In the future, it would be worthwhile to extend the SCOR model analyzes to further fields, especially to warehouse performance measurements.
-
Role of Lean and Agile Supply Chain Models for Pellet Fuel Technologies
119-130Views:148Business organisations constantly strive to improve their processes, both internal and external. Within the supply chain of a product, different strategies can be applied. This paper aims to answer the basic questions like what is the core of lean and agile SCM strategies, what are the differences of the two models, and how can they be combined. This paper examines further, which of these SCM models and what elements of them can be applied for wood pellet supply chains, also examining the possibility of their combination. The result of these examinations is, that even though fuel pellets can be considered as simple commodity and not a very innovative product, diversity in input characteristics, optimization of fuel pellet technology process variables and changes in output market qualities and quantities need sometimes agile, flexible answer from pellet fuel SCM. The basically lean character of pellet fuel technologies and SCM can further enhanced by implementing agile SCM model elements, as is the increased integration of suppliers into the supply chain.
-
Laboratory-scale gasification of brown coal and char from RDF pyrolysis
188-193Views:147The pyrolysis is a promising process for producing syngas from wastes. However, the by-product of the technology may contain large quantities of carbon, therefore it is suitable for further syngas production. In this paper we examined the steam gasification of brown coal from Felsőnyárád and char from RDF pyrolysis derived from an experimental pilot plant operating in Zalaegerszeg. We performed our experiments in a laboratory-scale fix-bed reactor at 900 °C. The aim of this work to examine the efficiency of syngas production from pyrolysis char, as well as to explore the similarities and differences of the thermal decomposition of the feedstock materials.
-
The Observation of Natural Analogies and Their Use in Design
27-32Views:98According to, Thomas Heatherwick, who was an English architecture, ‘The biggest object is a building’. [1] Nature has phenomenal problem solving skills – ‘Nature knows it better’. It has an impact on us and on our subconscious.
-
Analysis of a Special, 3D Metal-Printed HPDC Tool Material
251-265Views:168High Pressure Die Casting (HPDC) is still the most productive metal-casting method of our time, however the more demanding are the industrial expectations, the more challenging it becomes to ensure the creation of the difficult cavity geometries and the thermal balance of the die-cast tool. New perspective is required, thus we can utilize high heat-conductivity tool steels and additive manufacturing technology.
-
Sport Consumption, Fan Engagement, Sport Statistics – Post-specific Passing Characteristics in Football
Views:626Digitalization and the explosive development of technology have led to significant changes in football. Due to the increasing amount of data available through various sensors and other data collections, we can observe the rise of data-centric, analytical and statistically oriented thinking in football, which is also of interest to fans. Digitalisation is also closely linked to sports consumption, which is why we have seen significant changes in this area in recent years. The pandemic has further amplified the speed of digital transformation in the sports industry. One of the most important contents for sports organizations and their fans is the in-depth sports statistics and analysis that enhances the consumer experience. In our study, we examined the most common performance indicator in football, passing. Our goal was to examine the position-specific pass characteristics in detail, therefore we also examined different pass properties in our research. As a model for our analysis, I chose the premier league, which has the highest UEFA coefficient. The three rounds (rounds 30-32) of the championship season 2019/2020 have been recorded and analyzed in terms of passes. there was a significant difference between the average number of passes per game between defensive and offensive players (t=7,988, p<0.05). There is also a gradual decrease in the number of passes attempted per match and the accuracy of the pass in the examination of the middle positions when examining the positions in the depth of the pitch. For both pass accuracy and average pass count, the decreasing ranking corresponds to the position of positions on the pitch (order: 1, central defender 2, defensive midfielder 3, inside midfielder 4, attacking midfielder 5, striker). In the value indicator of the position for passes, offensive positions performed more effectively than defensive positions. The extreme positions also stand out among the attacking positions, where in the case of the position value per pass number, 23.3% of the total test was completed and 14% of the amount of the established position value indicators was provided by these posts. Overall, our study points to post-specific pass characteristics and, knowing this, we can state that the comparison of players' passing performance is relevant if the players are in the same or related positions.
-
Research of titration curves of red mud samples
270-276Views:92The aluminium demand is increasing worldwide, so the amount of red mud, which produced during the production of aluminium, is constantly increasing, also. The researching of the economical processing of the byproduct has been under way for a long time, but the industrial implementation of recovery technology, that is suitable in all aspects, has not yet been realized. The use of by-products, in addition to reduce the risk of contamination of environmental elements, may be useful for the recovery of valuable metals, which contained therein.
-
Self-developed Controller System –based on Open-Source Applications
97-105Views:94In the University of Debrecen Building Mechatronics Research Centre faced by the application of building automation technology, are tackled by cutting edge research performed at the Research Centre. The embedded device system, the focus of the ongoing project at the Research Centre, is programmable, reconfigurable, and adjustable. The design of an efficient embedded system must meet regulatory requirements, for optimizing building energy efficiency. The system provides solutions for a range of industrial applications, and peaks the interest of building services providers (e.g. SMEs).
-
The Possible Job Creation and Job Destructive Effects of Technological Development
53-61Views:308Throughout history, technological change has often provided the basis for employee anxiety. Between 1811 and 1816, a group of workers in England who called themselves "Luddists" destroyed machines, because they thought it would endanger their workplace. 19th-century thinkers and economists such as Karl Marx and David Ricardo predicted that mechanizing the economy would ultimately worsen workers' conditions, depriving them of a decent wage. Over the last century, John M. Keynes (1930s) and Wassily Leontief (1950s) have expressed their fears that more and more workers will be replaced by machine solutions that will lead to unemployment. In recent years, Brynjolfsson and McAfee (2014) have argued that existing technologies reduce the demand for labor and put some of the human workforce at a permanent disadvantage. However, there are a number of compensation mechanisms that can offset the initial displacement effects of automation and process innovation in general (Vivarelli, 2015). First of all, while workers are being replaced in industries that introduce new machine technology, additional workers in new industries are needed. Second, automation (and process innovation in general) reduces average costs. Acemoglu and Restrepo (2017) found that this results, on the one hand, in the effect of price productivity (“priceproductivity”) (as production costs decrease, the industry can expand and increase labor demand); and, on the other hand, it leads to economies of scale in production (the reduction in costs due to automation leads to an increase in total output and increases the demand for labor in all industries). Similarly, Vivarelli (2015) argues that lower average costs can result in lower prices (if the industry's market structure is perfectly competitive), stimulate product demand, or result in extra profits (if the industry's structure is not perfectly competitive). If these extra profits are reinvested in the company, this investment can create new jobs. The presentation intends to present these counterbalancing cases and to provide real examples based on the literature.
-
The Impact of Gas Flaring On Man and His Environment and the Way Out
82-90Views:145The nature of flaring processes has created a severe impact on man and the environment. Massive environmental degradation as a result of flaring activities has led to fluctuations in climate as well as depletion of the vegetation cover through acid rain. Findings have been made on some harmful gases released into the atmosphere that have effects on the environment and also on man. In order to control these effects by ensuring a clean atmosphere and environment, a new flaring model (DanMat flaring model) has been suggested. The model uses smoldering mechanism to reduce the amount of heat released into the atmosphere during conventional flaring by 60%. It also uses scavengers to oxidize harmful gas produced during flaring activities into less harmful ones. With this model one can flare gas without polluting the environment since it reduces the emissions of harmful gases during flaring.
-
Y Generation and the Job Seeking
490-501Views:1297Generations Y and their expectations have caused many surprises for employers. They are different compared to their predecessors. Millennials were born in socialism in our country, but they did not experience from it so much, because they grew up in democracy. Their main feature is that they are openminded to opportunities, and they learn quickly modern technology innovations. They have a strong self-conscious, and are highly proactive. They prefer forms of atypical work, because they can carry out their work anywhere in the world due to the internet access. It is very important for them to keep the work - life balance. These properties have overwritten the conventional management methods, such as conventional recruiting techniques. This paper examines the main job seeking features of the Generation Y based on an empirical research.
-
Efficient removal of salts from the residual dross of aluminium melting
259-269Views:114A residual dross of high quantity and high salt content arises from the hot (thermo-mechanical) treatment of the primary dross generated by the production of aluminium alloys from scrap. It contains a relatively low concentration of metal (5 – 10 %) but a high amount (30 - %) of chloride salts and some other components beside the oxide matrix. Due to the components dissolved in or reacted with water, this industrial residue - arising in thousands of tons also in Hungary – qualifies as hazardous and causes a real burden to the environment. According to the laboratory experiments aimed at an economical technology, the chlorides are dissolved within a few minutes when a liquid/solid ratio of 1:1 cm3/g (water volume:sample mass) is assured with an intensity of the horizontal shaking to prevent sedimentation. However, the filling ratio of the vessel also appears to have an effect. An implementation of relatively low cost would allow the recycling of the salt and the application of the final residue for alternative purposes.
-
The Measurement of The Three Components of The Cutting Force During The Turning Process
139-146Views:104We carried out the measurement of the three components of the cutting force as a function of the modification of the depth of cut during the longitudinal turning process. The results show that if we increase the depth of cut, all three components of the cutting force shows increasing tendency, regardless of how much the cutting speed and feed speed were performed during the measurements [1] [2] [3] [4].
-
Combustors with Low Emission Levels for Aero Gas Turbine Engines
503-514Views:359The aircrafts are responsible for emitting several types of pollutants, especially the pollutants in the form of NOX, CO2, CO, UHC, SOX and Particulate Matter PM (smoke/soot). The impact of aviation emissions on the global is well known, where these emissions modify the chemical and microphysical properties of the atmosphere resulting in changes of earth’s climate system, which can ultimate in critical changes in our planet fragile ecosystem, also the pollutants produced by aircraft engines cause many health problems. This is why the International Civil Aviation Organisation (ICAO) is seriously seeking to control the emission levels by issuing new standards during the successive meetings of the Committee on Aviation Environmental Protection CAEP (CAEP/01 in 1986, CAEP/2, CAEP/4, CAEP/6, CAEP/8, etc). The new regulations include more stringent standards aimed to reduce emission levels, this led to increased interest in low emission technologies. In this paper, a comprehensive review of low emissions combustion technologies for modern aero gas turbines is represented. The current low emission technologies include the high Technologies Readiness Level (TRL) including RQL, TAPS, DAC and LDI. Also, there are advanced technologies at lower TRL including LPP, ASC and VGC.
-
Analysing the Possible Connection Between Dark Triad Personality Traits and Ethical Attitudes of University Students
57-67Views:316In our paper we examined the possible connection between the Dark Triad personality traits and ethical attitudes among university students. The analysis of both topics has become the focus of interest in the past decades. Researchers consider the impact of many factors in the background of ethical attitudes and behavior. Among other things, personality is also a potential factor. The Dark Triad personality means the coexistence of the socially undesirable narcissism, Machiavellianism and psychopathy. Such people are characterized by self-love, aggression, the lack of guilt or conscience, so they are less likely to have ethical attitudes. In our research, this connection was examined by a questionnaire survey conducted among first year students of University of Debrecen Faculty of Natural Sciences and Technology and Faculty of Economics and Business. Respondents completed the validated Dirty Dozen questionnaire which was developed to measure Dark Triad personality and a questionnaire adapted from Lozier's research in which respondents were asked to evaluate school situations whether they are ethical or unethical and to what extent they are unethical. In our research, we were looking for significant relationships between the strength of the Dark Triad characteristics and the ethical judgment of situations. We also analyzed the differences between men and women and students of the two faculties.
-
Connection Between Human Excreta and Global Warming
139-154Views:191Our study would like to draw attention to an insufficiently investigated question: how human excreta and its different treatment methods are related to climate change. Human excreta is part of the biological cycle. Its CO2 content gets released to the atmosphere to some degree according to the treatment methods used. 40 55% of faeces’ and 11-17% of urine’s dry matter content is carbon (in the form of organic compounds). According to this, approximately 21-57 g/person carbon bound in organic compounds is produced daily, which means an emission of 58-183 million tons of carbon in the world annually in the form of human excreta. The environmental load of the widely spread flush toilet based water infrastructure is significant. However, neither the degree of CO2 emission caused by collection and treatment of waste water, nor wasting of organic and nutrient content of excreta are properly studied. Our study highlights the emission of CO2 caused by the energy demand of sewage water collection and treatment, by the oxidation of organic compounds of human excreta and by burning of methane produced as a result of anaerobic treatment of waste water sludge. Finally the possibility of utilization of human excreta by direct composting is presented, which technology has not significantly spread in the world yet.
-
Topology optimization and rim design
92-101Views:270A goal of this article is to show the development of the car wheel rims along with the progress of the manufacturing technologies over the past few years. To achieve this goal, topology optimization and generative design usage have been reviewed in this work. The research has focused on the main factors, which affect the life of car wheel rim, and it has shed the light on the effect of the topology optimization and the generative design on the manufacturing of the car wheel rims. Since the main factors above-mentioned are the: forces, material preferences and topology optimization, the study has covered the results of the studies made on each part along with the technology progress. Moreover, the article has explained the methodology main steps of the topology optimization and the generative design and their principles.
-
Development of a Small-Scale Plastic Recycling Technology and a Special Filament Product for 3D Printing
365-371Views:316In our days, the fight against pollution has become a real challenge for the state. recycling is one of the solutions that is adopted in several nations to reduce the rate of plastic discarded in nature. The amount of plastic waste has been increasing for decades contributing to the environmental pollution that is one of the most serious problem of the mankind. according to the statistics not only the household plastic waste, but the industry discharge is increasing because the utilization of plastic as a raw material is more and more extending. plastic can be found in a lot of products, huge number of bottles, plastic bags, computers, auto parts are sold every day. The current applications for using recycled plastics in fabrication and design are fairly limited, on a small scale, plastics (such as abs, HDPe1, or Pe2t) are shredded and formed into pellets, and then either extruded into lament to be used in existing 3d printers, or injection molded into small parts and pieces of larger components. at a large scale, recycled HDpE is melted into sheets and either used directly as sheets in construction, or then heat formed from a sheet into components for construction. these methods of fabrication using recycled plastics are the norm because of their straightforward processes. nevertheless, each method leaves some complexity to be desired. This paper we study the types of plastics and diagnose the pollution caused by the latter. this allowed us to design and size a recycling station of plastic into filaments for three-dimensional printers. this station which will contribute to the fight against pollution. the station consists of two machines for grinding of the plastic and the other for the extrusion of the desired filaments. we were able to make a theoretical academic study on both machines and also we designed with solidworks 2015. The theoretical study is spread of the mechanical calculations necessary to the design and validation of the structure using the tools. as the prospect of this project, we want to complete the achievement of this station while completing the crusher and extruder mechanically. then switch to electric and electronic parts (introduction of engines, sensors and wiring...). In the case of waste plastics that are recyclable and reusable. the most widely used are polyethylene terephthalate (pet, used for synthetic fibers and water bottles), and second high-density polyethylene (hdpe, used for jugs, bottle caps, water pipes).
-
Efficiency Analysis of Production Management System
401-415Views:206Due to the continuously evolving technology, even more escalating market competition has emerged between the companies. This competition is not only about the logistics related processes, it also appears to be significant for the production since the manufacturing companies form the center of global sale streams and without them the items found in logistical processes cannot be created. The role of production’s optimization and efficiency in the supply chain continuously grows since this is the part where a company’s most cost is produced. Our research objective was the examination of a company that applies various manufacturing, assembly technologies, and the used tools and softwares for this purpose were the SAP Business One ERP system and it’s add-on, called PPS One, the latter originated in Switzerland. We used these softwares to provide solutions to companies, especially to those that are dealing with manufacturing and production, for the optimization of their workflows, operations, supervising and controlling of their material. We also monitored from production technology’s elements the capacity planning, production orders, schedules, production tracking and cost accounting. We have made proposals during the analysis that might improve the company's strategy, competitiveness and increase it’s efficiency in business, and at the same time they can facilitate the company's pricing and inventory management activities.
-
The green methanol - playing a role in sustainable energy management
249-258Views:150Global energy demand is constantly increasing, so the energy sources we use, and the efficiency of energy use are of paramount importance for the future of humanity. Methanol can play a key role in the sustainable use of natural resources, in the efficient and smooth transition from a fossil oil-based energy system as well as in reducing greenhouse gas emissions. Long-term thinking will result in an increase in the use of renewable energy sources, which will favour the spread of green methanol technology and thus the use of a carbon-neutral fuel. The raw materials for the production of green methanol may include municipal solid waste, agricultural waste, renewable hydrogen and carbon dioxide and the methanol has many uses, both as fuel and chemical feedstock. It also provides an opportunity to chemically store excess renewable energy from intermittent sources, thereby reducing dependence on fossil fuels. The price of electricity used for electrolysis is the main determinant of the economical production of green methanol, so the reduction of the cost of solar and wind energy greatly contributes to the competitiveness of carbon-based production.
-
Solutions of Warehouse Technology in Connection with Management Decisions
1-10Views:140The aim of the study is to analyse the effect of management decisions on space utilization of warehouses through two companies’ example. The only way to make good decisions is to take into consideration the possible effects of changes. One of the tire manufacturing companies managed to improve space utilization, caused not only time but cost reduction. On the contrary, a bad decision of a household chemical factory induced enormous problems in the material flow.
-
Requirements for Multicultural Competencies Defined by a Focus Group
44-56Views:197Globalization, the spread of multinational companies and the enormous development of information technology can lead to a new trend in employers’ requirements. However, being employed by an international company is a real possibility for any employee in any part of the world. Even if they do not have to work abroad, employees may have to function in a multinational environment in their home countries. A favourable combination of intercultural competencies is a key factor in the selection and development of employees. A possible way of measuring these competencies can be the Multicultural Personality Questionnaire (MPQ). First of all,on the employers’ part, it is important to clarify the exact requirements and competencies (dimensions) to be able to draw up an ‘ideal profile’. We prepared two versions of the MPQ (91-item; 5-dimensional) and used them to test employers’ requirements in the selection process regarding the dimensions of cultural empathy, open-mindedness, social initiative, emotional stability and flexibility. This study describes the results of a focus group interview, which took place in 2017, revealing the importance of multicultural competencies from the employers’ point of view and examining the conditions of the adaptability of the two questionnaires. We used the focus group method to find out in what conditions the questionnaires canbe used in a selection process. What possibilities and limits are therefor using the direct five-dimensional questionnaire? What aspects do we need to take into consideration in expressing and interpreting the requirements in the results of the test?
