Search
Search Results
-
Methodology adaptation and development to assess salt content dynamics and salt balance of soils under secondary salinization
199-206Views:143The effect of irrigation with saline water (above 500 mg L-1) is considered a problem of small-scale farmers growing vegetable crops with high water demand in the hobby gardens characteristic of the Hungarian Great Plain. In order to simulate the circumstances of such hobby garden, we set up an experiment including five simple drainage lysimeters irrigated with saline water in the Research Institute of Karcag IAREF UD in 2019. We regularly measured the electric conductivity (EC) of the soil referring to its salt content and the soil moisture content with mobile sensors. Before and after the irrigation season, soil samples from the upper soil layer (0-0.6 m) were taken for laboratory analysis and the soil salt balance (SB) was calculated. The actual salt balance (SBact) was calculated of the upper soil layer (0-0.6 m) based on the salt content of the obtained soil samples. The theoretical salt balance (SBth) was calculated by the total soluble salt content of the irrigation water and leachates. During the irrigation season, we experienced fluctuating EC in the topsoil in close correlation with the soil moisture content. Based on the performed in-situ EC measurements, salts were leached from the upper soil layer resulting in a negative SB. Combining SBact and SBth of the soil columns of the lysimeters, we estimated the SB of the deeper (0.6-1.0 m) soil layer. We quantified 12% increase of the initial salt mass due to accumulation. We consider this methodology to be suitable for deeper understanding secondary salinization, which can contribute to mitigating its harmful effect. By repeating our measurements, we expect similar results proving that saline irrigation waters gained from the aquifers through drilled wells in Karcag are potentially suitable for irrigation if proper irrigation and soil management are applied.
-
Strategic planning in agribusiness
23-27Views:145Agricultural businesses operate in a complex and dynamic environment, with many challenges and opportunities. It is therefore essential for these businesses to have a strategic plan. It is a critical process that helps businesses navigate in a complex and uncertain environment and achieve long-term goals and objectives. In this article, we have conducted a bibliometric analysis of academic journals to investigate the extent to which strategic planning is a researched topic in agribusiness enterprises. We found that there is no concentrated research, with only three keywords appearing in the literature with at least five repetitions. Even of the two repetitions, only 22 were found. The clustering of keywords helps to identify research directions. The results of a survey of 134 enterprises were then presented. The majority of enterprises do not have a long-term plan or even a written vision. We found that SWOT analysis is still the most common planning method among the companies surveyed. It was also found that there is no difference between industries in this respect. Significant differences were only found in relation to company size, with all large companies having a strategic plan and the vast majority of SMEs not. Only 17 out of 132 firms have a plan longer than three years, and 32 do not have any plan at all. Strategic planning can help to address many of the challenges in the agribusiness area, and it is therefore proposed to improve the proportion of firms planning through knowledge transfer.
-
The methodology of the Hooded Crow’s (Corvus cornix L.) colour ringing and the previous results
43-48Views:150The Hooded Crow (CorvuscornixL.) have moved in several Hungarian cities in the last few decades. It is breeding in Debrecen since 1959, and nowdays it’s presence can be detected at all points of the city, it is an permanent breeding species of the bird fauna. Our knowledge about the nature of urban races, including motion patterns, area fidelity is sufficiently incomplete. The aim of our research is to answer these questions by using our colour-ring program. In this study we present in details the methodology of Hooded Crow’s colour-ring program in urban area, and we also report our previous
achievements. -
Opportunities of delineating inland waters and soil moisture with remote sensed data
95-98Views:106The methodology for delineating water bodies on multispectral remote sensing imagery was examined and evaluated. A supervised approach is tested with the aim to accurately detect inland water, moisturised soil surface and swampy patches on the Landsat TM 7 scene. The goal of this research is to investigate whether the application of remote sensing image interpretation could further refine the possibilities of future soil conductivity measurement research. The methodologies used were the application of supervised classification algorithms based on the training data collected in the area. The achieved overall classification accuracy value of 83.0795% suggests that the methodology could be used as a successful strategy to incorporate remote sensing data interpretation into soil conductivity measurement planning and application. The main conclusion that can be drawn is that processing of multispectral data with further refinement of the presented methodologies can led to very useful outcomes for environmental measurements.
-
Interpretation of sustainability in the utilization of renewable energy sources
61-64Views:102The utilization of renewable energy sources (res) is crucial regarding to sustainable reconstruction of energy systems. The target is a balanced, sustainable development of Hungarian energy management considering equally the ecological, social and economic aspects. There are many different technologies of utilization of res varied by sources, conversion processes, size and products. The comparison of each technology and their sustainability assessment are required by the importance of efficient remodeling of energy infrastructure. The group of attributes was composed by numerous important parameters in the course of our analysis with the choice experiment (ce) methodology. The estimation of each attributes’ influence on the individual’s preferences and choices was possible by this method and the preferences of the statistical population was concluded. So thus the utility derived from each attribute was estimated. The result of the ce analysis for the population of experts is demonstrated in the current phase of our research.
-
Survival analysis of sow longevity and lifetime reproductive performance – Review
75-80Views:256Sow longevity plays an important role in economically efficient piglet production. Improving sow longevity results increase in the productivity and profitability of a sow herd. Longevity is a complex trait with many factors that can contribute to a sow having a long and productive life. Not only the sow’s genetics, but also nutrition, environment and the management policies are important. In addition, the removal of non-productive sows along with the introduction of replacement gilts is an essential part of maintaining herd productivity at a constantly high level. The objective of this paper was to summarize the current knowledge about the sow longevity and lifetime performance values, as well as, discusses the survival analysis methods for sow longevity traits. This method can estimate the hazard rate indicating proportional risk of sows being culled at any given time, in addition, it is able to investigate the effects of different factors on longevity. Identifying factors that influence the longevity could assist many commercial pig producers in becoming more efficient.
-
Terrain Analysis and Stochastic modelling for Archaeological site prediction and landscape reconstruction in the Lake Manyara area, Northern Tanzania
47-53Views:169In this study we focus on paleontological sites in the area of Lake Manyara and the Makuyuni River Basin, Northern Tanzania. This region is known for Middle Pleistocene fossil finds and artefacts. To analyze the spatial distribution of potential paleontological find locations we applied two different methodologies based on statistical mechanics and on boosted regression trees. The first one is able to handle presence-only datasets such as the locations proper. The second approach was used to study the variable importance and to derive information on the related geo-processes for classified paleontological sites. The locations and their spatial distribution were retrieved from literature and collected by own field work over the last years. For the modeling we utilized environmental information such as spatially continuous layers of topography (30 m SRTM DEM), derivatives of topography, vegetation information as well as ASTER multispectral data as predictor variables. The results reveal
potential areas where further fossil sites may be located. Moreover, we assessed the processes that are related to sites with specific archaeological evidences. Therefore, the sites were grouped in three categories: i) artefacts sites, ii) fossil sites and iii) mixed sites. We applied boosted regression trees to analyse the processes related to the classified sites. The methodology considers not only site specific characteristics but implicitly also the related pedogenetic and morphogenetic processes. We were able to differentiate between artefact and fossil sites. Moreover, our analyses indicate an influence of transportation processes on the artefacts, whereas deposition of fossils does not seem to involve large scale transportation. Finally, we show that also the landscape can be reconstructed such as the former lake margin. -
Application of molecular genetic methods for birds (literature review)
37-41Views:121Ornithology studies have been extended by molecular genetic techniques. In this paper we are dealing with the most common use of areas. Our basic aim is to give a comprehensive view of the most commonly used methods in ornithological studies, including the available results by their use. We also deal with the following areas: an essential step during examination namely the applicability of sample collecting methods, and the unique identification, also the sex determination, methodology of DNA barcoding, as well as the role of molecular methods to protect endangered species. We discussed the advantages and disadvantages of the methods, such as the current trend for each method.
-
Examination of repeatability of ultrasound scanning technique in young bulls
43-48Views:109The author’s goal with the methodology examination was to determine repeatability of taking and evaluating ultrasound images. In the trial an operator person took two images about the ribeye area and rump fat thickness (P8) of every young bull, which were measured by the same person in four repetitions. Also, we had altogether eight images about the same part of the body. Images were collected using Falco 100 (Pie Medical) real-time ultrasonic scanner equipped with an ASP 3,5 MHz, 18 cm linear array transducer.
-
Examination of soil parameters based on the evaluation of the spectroradiometric reflectance characteristics of the topsoil
75-80Views:134In this article we are presenting the methodology applied to analyse and interpret the topsoil surface reflectance parameters of multiple samples collected in the Mugello valley area in northern Italy in October 2012. The main aim of the whole project was to discover geomorphological behaviour and situation of the area ino order to improve potential for correct dating of certain archaeological artefacts found in the nearby areas. One of the crucial problem researchers are facing in the area is the lack of understanding of the underlying geological and geomorphological processes that were describing and characterizing the area and that played important role not only in the current geography and landscape formation but also in the transportation of various sediments and artefacts. In this particular research the main aim is to examine the possibility of developing a quick way to assess low level properties of the soil using hand held spectrometer and rapid analysis of cross-section using in situ measurement techniques. In this work we collected over 2000 individual samples of topsoil surface reflectance properties that we organized into a spectral library. This library is then to be used to describe physical and chemical processes in the soil. To support the analysis results were compared to analysis results from different kind of assessments in the same area. Our results show a great potential of application of hand held imaging spectrometer in soil property analysis based on the top soil surface reflectance parameters.
-
Heat-No-Service: Reproductive lifetime performance of gilts inseminated on first versus second observed estrus in commercial piglet producing herds
77-80Views:262Heat No Service (HNS) is an increasing managerial decision made in commercial piglet producing herds. Performance of gilts has been shown to be influenced by initial decisions made on them at their introduction in the breeding herds. Lifetime Reproductive performance comprising of parity total born piglets and lifetime total born piglets of gilts initially bred on first observed estrus (0HNS) was compared with that of gilts bred on second observed estrus (1HNS). Stored data from Porcitec database consisted of 2.072 gilts bred on first observed estrus (0HNS) and 2.453 gilts bred on second observed estrus (1HNS) totaling to 4.525 gilts. Data was statistically analyzed using the GLM procedure of IBM SPSS version 25. The results showed a significance difference (p<0.001) in lifetime total born performance of gilts bred at 0HNS (mean 93.9) and 1HNS (mean 95.7). There was also a significant difference (p<0.001) of total born piglets in parity 1, 5 and 6 in the 2 groups. There was an observed increased parity total born and lifetime total born when first time insemination of gilts was delayed to second estrus. The findings in this study favor the 1HNS breeding with an overall increased lifetime total born. Gilts inseminated at 1HNS produce 1.57 more pigs for lifetime as compared with those inseminated at 0HNS when observation is made up to P6. Producers in piglet producing herds could re examine their decisions for increased productivity by promoting many gilts into 1HNS but still maintaining the balance between breed targets and production schedules to remain competitive and profitable in the current global swine industry.
-
Mapping agricultural performance and environmental parameters aimed at generic regional studies
29-34Views:151In this paper we present the interim results and the methodology applied to create web GIS ready cartographic representations of agricultural performance related information and environmental parameters. The main aim of the research is to eventually create a web GIS based decision support system that can enable decsision makers and general users to create useful and representative map layouts of certain environment and agriculture related phenomena that can be easily analyzed and interpreted to make strategic decisions on environmental issues. In this aim the initial steps are to evaluate the available data for cartographic representation, analyze the possibilities of visualization, create a GIS ready data structure and implement the database and revise additional possibilities to incorporate further environment related datasets of auxiliary sources. The main results of the study are a comprehensive set of visual layouts that could serve as guideline for mapping statistical information of agriculture and some steps towards the incorporation of environmental parameters to the system.
-
Sight-specific development of the tools for the measurement of CO2-emission of the soil
53-58Views:81Soil is the main source and at the same time the potential sink of greenhouse gases (e.g. CO2, CH4). Measurements were carried out in the experimental sites (soil tillage experiments and an extensive pasture) of the Karcag Research Institute of University of Debrecen, Centre for Agricultural Sciences to determine the CO2-emission of the soil. The in situ CO2-emission of soil was measured by means of an ANAGAS 98 infrared gas analyser in plastic (PVC) chambers, but this previously applied method (cylinders) was not suitable for the soil surface covered with grass,
hence a new instrument was needed to be invented. In order to measure CO2-emission on a larger area without deep disturbance of the soil, a special metal frame was created with a matching bowl. The most problematic part was the spatial delimitation of the measurement area as the surface of the soil can be very various and proper isolation is a must. We consider the frame+bowl method we developed suitable for measuring CO2-emission of pastures as well as other crop-fields. -
A simple but powerful tool for the assessment of financial progress in EU co-funded grant programmes – Simple Progress Overview Tool (SPOT)
67-72Views:118Mid-term evaluation of grant programmes always aim to assess the financial progress of the programme. Progress to date assessment is conducted via addressing three issues: by overviewing progress so far, by exploring the reasons behind the current level of progress, and by answering the specific evaluation questions formulated as a result of progress overview. The Simple Progress Overview Tool is a method and a tool facilitating the overview of financial progress, supporting the exploration of reasons behind the current level of progress and enabling the identification of targeted further evaluation questions. The methodology applies the Du Pont approach of division to factors, in which the variable describing a phenomenon is divided into the multiplication of factors (milestone stages of the process) influencing the variable. Also, this division to factors facilitates the identification of reasons behind progress. The factors carry individually meaningful information to the evaluation of progress. This method was used by many EU member states including the Czech Republic, Romania, and Malta for the evaluation of progress in the course of the mid-term evaluation of their National Strategic Reference Frameworks.
-
Examination and statistical evaluation of physico-chemical parameters of windrow composting
33-38Views:192The treatment and utilization of plant and animal waste and by-products from agriculture is very diverse. Traditional environmental management practices for waste management have been retained through soil conservation and the applied of recycle degradable organic substances in soil. The management of by-products from agriculture (animal husbandry) is important because a closed loop can be created to utilize by-products (manure, feathers) from the production of the main product (eggs, meat, milk) and to form a raw material for a new product. It is important to treat the resulting by-products, especially deep-litter manure, as it has served as a basis for compost-treated manure to develop an organic-based, soil-conditioning product line. Poultry manure by itself is not suitable as a substrate for aerobic decomposition, so it has to be mixed with other substances (zeolite, bentonite, soil), because of its high nutrient capacity, it is an acidifying substance.
The aim of this study was to compost the mixture of poultry manure and hen manure by the addition of zeolite and to monitor the composting process. It was also our aim to statistically determine the effect of the zeolite on parameters describing the composting process.
The windrow composting experiments were set up in the composting area of the University of Debrecen, Institute of Water and Environmental Management. The composting experiment was 62 days long, during which the main parameters describing the composting process were continuously monitored: temperature (°C), moisture content (w/w%), electrical conductivity (mS/cm), organic matter content (w/w%), examination of nitrogen forms (w/w%). In this study, three factors were investigated: temperature, humidity, and pH. For statistical evaluation, R software and RStudio user interface were used. We developed a repeated measurement model, in which the fixed and random effects were determined for our parameters under study, and the resulting relationships were shown on interaction plots.
Based on our results, the temperature of the prisms has become independent of the ambient temperature and the composting stages can be separated in both the control and the zeolite treated prisms. In the repeated measurement model, we proved that treatment, time and treatment: time interaction were significant at both temperature and pH.
-
A new model for predicting carbon storage dynamics and emissions related to the waste management of wood products: introduction of the HWP-RIAL model
75-81Views:96The ability of wood products to store carbon allows for their significant contribution to the climate mitigation efforts and the emission reduction commitments set by the EU. In order to optimise the carbon storage capacity of wood products, it is important to take climate mitigation aspects into consideration as much as possible during their production, use and waste management. The aim of this study was to quantify the effects of product development, recycling, and waste management technologies on carbon storage and emissions. In the frame of the ForestLab project, a new model and decision support tool was developed, which is able to predict the duration of carbon storage of wood products and the evolution of emissions from them. The developed HWP-RIAL model (Harvested Wood Product Recycling, Incineration And Landfill model) uses the methodology of the Intergovernmental Panel on Climate Change (IPCC) to calculate emissions, which is also used in the National Greenhouse Gas Inventory report. It combines the IPCC waste model with equations describing the carbon storage and emissions of wood products, and the model is also supplemented with a self-developed recycling and waste routing module. This paper provides insight into the operation of the model by following the life cycle of 200,000 m3 particle board.
-
Methodologies in measuring risk of financial statements
117-120Views:65Aim of financial statements’ risk analysis is to optimally allocate the audit resources. That optimum point can be reached, if we achieve maximum possibility of recovery of material risks. There are more than one procedures exist for researching of optimum point or risk assessment in other word, and they are needed to use even parallel. In order to take into consideration effects of risk we need to measure them somehow. At risk assessments risks are usually some kind of result of impact and possibility. Knowledge and measurement of impacts and possibilities are far not enough for assessment of certain risks. In this study I will present a possible usable risk assessment methodology for financial audit activities with using Multi Attribute Utility Theory (MAUT in the followings).
-
The measurement of successfully completed projects funded by the European Union
9-12Views:134Projects funded by the European Union contribute significantly to the socio-economic development of Hungary, its increasing competitiveness, thereby the local people's general level of satisfaction, their ”happiness and prosperity”. Successful spending from the Union's funds, successful project implementation directly impacts all actors in the Hungarian economy and society. Therefore, to examine the factors that support or jeopardize the implementation of the projects is a priority at EU and national levels. My research and doctoral dissertation aims to develop a methodology to assess the management efficiency of projects supported by the European Union, implemented in Hungary taking into account all measurable factors (technical and special expertise) and the "suspected" factor (EU thinking learning).
I intend to draw up guidelines for future EU funded project management teams to realize projects successfully for the benefit of Hungary.
-
Optimal age of breeding gilts and its impact on lifetime performance
15-20Views:497Age at first breeding and lifetime reproductive performance was analyzed on 17,558 F1 Landrace x Yorkshire gilts from 9 piglet producing herds of Midwest, United States entered in herds between 1st Jan 2014 and 31st July 2016. At the time of data collection Dec 2018, 15% of the sows were still active in the herds hence excluded from the analysis. Individual gilt data included date of birth, age in days at first mating, piglet total born by parity, lifetime piglet total born and reason for culling. Quality data checks were done before analysis to eliminate all outlier values together with sows that had no entry information for any listed category. The total database of the sows was classified into 6 classes according to age at the first mating in days 170-190(n=754), 191-211(n=4683), 212-232(n=7123), 233-253(n=3385), 254-274(n=1002) and 275-369 (n=611). Piglet total born obtained from each sow during the lifetime production was significantly (P < 0.05) greater for gilts bred between 233-253 days of age at first mating. Gilts that were bred at <233 days appeared to have a higher risk of removal by farrowing productivity as compared to the other groups. However, the results show that the risk of being culled due to health problems and conformation issues increases as the age at first mating is delayed. Overall reproductive failure appears to be the most economical culling reason across all age groups. There is a need to evaluate the best management decisions for gilt initiation in a herd to maximize her lifetime performance. The results indicate that gilts mated for the first time at the right age, 233–253 days, are more productive, both in lifetime total born and have a minimal risk of culling due to farrowing productivity.
-
Characterisation of basic water balance parameters of Debrecen
35-40Views:169This work aims to develop a hydrological modelling tool to help managers make the right decisions for Debrecen, in the face of water scarcity and the increase in agricultural and domestic needs over time. The methodology was based on the creation of a climatic database, at monthly time steps, from 2016 to 2019, and cartographic (land use, digital elevation model, and hydrological network). As a next step, the watershed was delimitated into sub-basins to determine the shape and the physiographic characteristics of sub-watersheds. Finally, a hydrological study was prepared by calculating the time of concentration to build a database of water resources in the study area. This water resource will be used as an input parameter for urban farming.
-
Sow removal patterns in commercial breed-wean herds of Midwest, USA
9-14Views:330An observational retrospective study was done to provide up-to-date information on recent sow removal patterns from 9 breed-wean herds of Midwest USA. The study comprised of sow’s removal reasons and removal types of F1 Landrace x Yorkshire gilts entered in the herds between 1st Jan 2014 and 31st July 2016. Data was extracted from existing database on Dec 2018 and 15% of the sows were still active in the herds hence not included in the study. Descriptive statistics showed that out of the 20,009 removed sows, planned removals comprised of farrowing productivity (FP) 3,523 (17.6%) and old age (OA) 1,785 (8.9%) while unplanned removals consisted of reproductive failure (RF) 7,786 (38.9%), health problems (HP) 2,629 (13.1%), locomotion problems (LP) 1,473 (7.4%) and conformation issues (CI) 1,350 (6.8%).‘Did not conceive’ and “No heat” were observed as the main contributing factors accounting for 37.6% and 32.9% respectively for gilts & sows removed by RF.13.5% of the gilts (Parity 0) were removed from the herds before attaining their first litter of which 64.1% of their removals was due to RF. Removal type consisted of slaughter (S) 85.0%, found dead on the farm (DoF) 10.8% and euthanized (E) 4.2%. The research findings depict an upward trend of sow RF removals in the US swine herds posing a serious concern for US swine producers. Characterization and quantification of sow removals gives a revelation on the deeper intrigues about the vulnerability of the various parity in respect to common causes of RF. This helps swine producers to decisively improve on gilt replacement selection, reproductive efficiency, health and nutrition management all aimed at increasing overall swine productivity and efficiency in management. Swine farmers in the US can now focus their efforts towards curbing unnecessary RF removal within parity specifics.
-
Challenges in the mangalitsa sector – present and future
147-153Views:120The Hungarian mangalitza pig sector has experienced numerous structural changes in the past few decades. The increased demand in the foreign markets for the mangalitza pork, changes in the domestic consumer perceptions have increase the number of sows and breeders. After the European Union’s accession started a significant growth in the sector, which was due to the target programme from the year of 2005 for the keeping of animals representing high genetic value, as the breed is indigenous. From 2008 continuous decline can be observed. The main reason for the decrease was the drastic growth of feed costs because of the drought damage in 2007, and the global economic crisis. Since 2010, a further period of supports has been in place, it extands the willingness to keep mangalitza pigs and the number of sows continuously increasing. On the basis of the average farm size (58 sows/farm) in 2011 it can be stated, that after our EU’s accession the medium-sized farms became stronger. To evaluate the geographic concentration of the mangalitza livestock it was analysed the data of sow number among the years of 2000 and 2011. The geographic concentration of mangalitza stock has a medium value over each year under the survey period, except the years of 2004–2007, when the values of Herfindahl-Hirschman index (HHI) have low degrees. Due to the subvention period of indigenous breeds it was established more mangalitza farms in different parts of Hungary. Despite of the growth since 2000, numerous problems are in the segment. The aim of the study is to find out the sectoral problems, which are completed with the objectives tree and draw up the main activities to solve the problems. After estimating the SWOT-matrix according to the methodology of the strategic analysis and the discussions with the secretary of National Association of Mangalitza Breeders is prepared the sectoral problem- and objectives tree. The core problem of the mangalitza sector is that the origin of mangalitza products are not certified in the domestic markets. The reason of it is that the breeders don’t request the certificates of fattening pigs, so it can appear not real mangalitza product on the markets as mangalitza. To solve the problems it is drawn up different suggestions in the objectives tree. This analysis is an useful tool for the decision makers in the mangalitza sector to evolve strategic plans on behalf of the efficient cooperations among chain actors.
-
Estimation of direct and maternal genetic parameters for weaning weight in Hungarian Simmental cattle
17-22Views:134The aim of the current research was to estimate variance components and genetic parameters of weaning weight in Hungarian Simmental cattle. Weaning weight records were obtained from the Association of Hungarian Simmental Breeders. The dataset comprised of 44,278 animals born from 1975 to 2020. The data was analyzed using the restricted maximum likelihood methodology of the Wombat software. We fitted a total of six models to the weaning weight data of Hungarian Simmental cattle. Models ranged from a simple model with animals as the only random effect to a model that had maternal environmental effects as additional random effects as well as direct maternal genetic covariance. Fixed effects in the model comprised of herd, birth year, calving order and sex. Likelihood ratio test was used to determine the best fit model for the data. Results indicated that allowing for direct-maternal genetic covariance increases the direct and maternal effect dramatically. The best fit model had direct and maternal genetic effects as the only random effect with non-zero direct-maternal genetic correlation. Direct heritability, maternal heritability and direct maternal correlation of the best fit model was 0.57, 0.16 and -0.78 respectively. The result indicates that problem of (co-)sampling variation occurs when attempting to partition additive genetic variance into direct and maternal components.
-
Information and Communication Technologies in tourism
49-53Views:146Technological progress and tourism have gone hand in hand for years. Information communication technology (ICT) and tourism are two of the most dynamic motivators of the emerging global economy. Tourism can be considered as one of the most profitable sectors of the Hungarian economy, and in rural areas it is often the only successful economic activity.
Development of ICTs and the expansion of the Internet have changed dramatically in the past few decades. This process is noticeable in
Hungary, as well. Platform of tourism increasingly get to the Internet nowadays, which is vitally important because tourism is an information-intense industry. Therefore, it is critical to understand changes in technologies in order to maintain the crucial role of this sector in the Hungarian economy.
The aim of my study is to support the significance of tourism in Hungary and especially in the North Plain Region with the help of statistical data. Then, I try to show how ICTs appear in this sector and emphasize the role of these tools with some concrete examples. -
Chromatometric comparison of Eurasian Collared Dove (Streptopelia decaocto) and Feral Pigeon (Columba livia domestica) feathers
19-22Views:176Chromatometric examination of the plumage of birds is a poorly researched topic. We have approached this issue in primarily aspect of differences in plumage of species. Moulted feathers sample collection method has been increasingly used. Reliable identification of feathers becomes an increasingly important issue, hence need for an exact measurement-based methodology. Eurasian Collared Dove (Streptopelia decaocto) and Feral Pigeon (Columba livia domestica) primary, secondary and tail feathers were studied. Chromatometric parameters of feathers were measured in CIELAB color system and then statistical analysis (Independent samples t-test, Descriptive Statistics, Discriminant Analysis) was performed to compare the two species. Instrumental measurements has been confirmed the high similarity between colors of the two species, however species specific differences were also found. Lightless (L*) value were significantly characteristic of particular species, while the red/green (a*) and yellow/blue (b*) value had lower Predictive Power. We identified feathers and the variables which useable to separate the two species and determined the associated Confidence Intervals of these values. Our results may draw attention to a new potential direction for exact identification of the moulted feathers during sample collection.