Search

Search Results

• Bond-Graph Model Based Stepper Motor Output Characteristics Simulation Implemented in LabVIEW Environment

  1-6.

  Zsolt Molnár

  Géza Husi

  Views:

  324

  In the industry, simulations are of great importance. They enable measurements to be made in different conditions about a virtual device, which are highly comparable to measurements made in a real life scenarios. Because of their wide range of usage in lower power drive systems, where precision and simplicity is a must, the subject of study is a permanent magnet stepper motor. For precise positioning purposes, it is essential to know the positioning behaviour of these devices. The model construction process involved an intermediate step, which consisted of creating the Bond-Graph of the motor based on pre-defined models available in the literature in this field. In the next step, the Bond-Graph model was converted to a block diagram of the motor. This permitted the direct implementation of the motor model in LabVIEW visual programming environment. The preliminary steps allows us to check and confirm the functionality and correctness of the model. This article covers in detail the model conversion and implementation steps of the simulation. At the end, the functionality of the simulation was tested.

• Bond Graph Modeling, Simulation, and Control of Permanent Magnet Linear Synchronous Motor: PMLSM Motor Based EVs Applications

  1-9

  Aminu Babangida

  Géza Husi

  Péter Szemes

  Views:

  211

  The high-performance feature of the Permanent Magnet Linear Synchronous Motor (PMLSM) makes it a reliable and valuable motor for use in the automotive industry, especially for electric vehicle (EVs) applications. This research proposes a bond graph approach in modeling the PMLSM as a multi-domain dynamical system.

  However, A time-based simulation was performed using 20-sim software to simulate the dynamical behavior of the motor. An equivalent model of the motor was first obtained and then modeled and simulated using 20-sim software. The model of the PMLSM drive system was modeled separately and incorporated with PMLSM Motor equivalent model to form a global model.

  Moreover, the motor drive system response was studied based on the sensor resolutions and the inverter switching frequency. The block diagram and the transfer function methods validated the bond graph model obtained. Two classical PIs such as continuous and discrete were implemented on the motor response to control the velocity of the motor.

• Brushless DC Motor Modeling Using Bond Graph Method and Control using LabVIEW: Speed control based calssical PID control

  1-5.

  Ammar Alsabbagh

  Péter Tamás Szemes

  Abdulkader Baki

  Views:

  262

  This paper aims to simulate and control a three-phase Brushless DC Motor. Bond Graph method has been used to obtain fast and simple dynamic model. The system has been controlled by classical PID controller. All the paper results were fulfilled using LabVIEW program.

• Modelling and Simulation of Stepper Motor For Position Control Using LabVIEW

  1-5.

  Ahmet Mehmet Karadeniz

  Malek Alkayyali

  Péter Tamás Szemes

  Views:

  1763

  This paper presents hybrid stepper motor (is a type of stepping motor) modelling and simulation which is widely used a kind of motor in industrial applications. In this study, the stepper motor was modelled using bond graph technique and simulation for desired position was executed on LabVIEW
  graphical interface. Then, firstly a convenient PID controller was designed for position, speed and current and PID close loopresponse was obtained for position control. Then, PID parameters for each controller were arranged separately to obtain good response Secondly, Fuzzy Logic controller applied to
  the system and its response was obtained. Finally, both responses are compared. According to comparison, it was observed that Fuzzy Logic controller’s response is better than PID’s. (In this paper, all shown responses were observed for 120 degree desired position)

• Speed Control of Three Phase Induction Motor Using Scalar Method and PID Controller

  1-5.

  Aram Nasser

  Péter Tamás Szemes

  Views:

  247

  This paper presents the speed control of a three-phase induction motor using the scalar control method with PID controller. The system maintains a constant volt to frequency ratio for any change in the load. We also used vector control method and bond graph to describe the motor model, as well as its behavior. Finally, we simulated the system using Labview, where the good results of using the scalar control technique are shown.