Évf. 8 szám 1 (2023)

Anyagtudományok

Mechanical Testing of 3D Metal Printed Stainless Steel Specimens

Megjelent:

2023-04-30

https://doi.org/10.21791/IJEMS.2023.1.2.

Szerzők

Kovács Sándor Endre,

University of Miskolc, Faculty of Materials and Chemical Engineering, Institute of Foundry Engineering

Varga László

University of Miskolc, Faculty of Materials and Chemical Engineering, Institute of Foundry Engineering

Megtekintés

PDF (Angol)

Kulcsszavak

Additive manufacturing (AM) 3D metal printing tensile testing selective laser melting powder bed fusion

Licenc

Copyright (c) 2023 Sándor Endre Kovács, László Varga

This work is licensed under a Creative Commons Attribution 4.0 International License.

Hogyan hivatkozzuk

Kiválasztott formátum: APA

Kovács, S. E., & Varga, L. (2023). Mechanical Testing of 3D Metal Printed Stainless Steel Specimens. International Journal of Engineering and Management Sciences, 8(1), 7-13. https://doi.org/10.21791/IJEMS.2023.1.2.

Hivatkozási formátumok

Hivatkozások
• ACM
• ACS
• APA
• ABNT
• Chicago
• Harvard
• IEEE
• MLA
• Turabian
• Vancouver
• AMA

---

Letölthető hivatkozások
Endnote/Zotero/Mendeley (RIS) BibTeX

Beküldött 2023-01-17
Elfogadott 2023-02-05
Publikált 2023-04-30

Absztrakt

Additive manufacturing (AM) is a cutting-edge production method, which has come a long way since its first introduction in the ’80s. Back in the days its usage was very limited to stereolithography, and was only able to make weak structures, so it only worked for visualization. Four decades later it is one of the leading research fields in production areas, because of its flexibility and its ability to make almost any complex geometry. However, no matter how powerful it is, it is not omnipotent, there are certain size and shape restrictions even this method must apply to.

Hivatkozások

1. Davide Sher, 3D Hubs Publishes Complete 3D Printing Technologies Infographic » 3D Printing Media Network - The Pulse of the AM Industry, https://www.3dprintingmedia.network/
2. Yadollahi, A., Shamsaei, N., Thompson, S. M., Elwany, A., & Bian, L. (2017). Effects of building orientation and heat treatment on fatigue behavior of selective laser melted 17-4 PH stainless steel. International Journal of Fatigue, 94, 218–235. doi:10.1016/j.ijfatigue.2016.03.014
3. Alsalla, H. H., Smith, C., & Hao, L. (2018). Effect of build orientation on the surface quality, microstructure and mechanical properties of selective laser melting 316L stainless steel. Rapid Prototyping Journal, 24(1), 9–17. doi:10.1108/rpj-04-2016-0068
4. Pal, S., Gubeljak, N., Hudak, R., Lojen, G., Rajtukova, V., Predan, J., … Drstvensek, I. (2018). Tensile properties of selective laser melting products affected by building orientation and energy density. Materials Science and Engineering: A. doi:10.1016/j.msea.2018.11.130
5. Tridello, A., Fiocchi, J., Biffi, C. A., Chiandussi, G., Rossetto, M., Tuissi, A., & Paolino, D. S. (2020). Effect of microstructure, residual stresses and building orientation on the fatigue response up to 109 cycles of an SLM AlSi10Mg alloy. International Journal of Fatigue, 105659. doi:10.1016/j.ijfatigue.2020.105659
6. Zhao, J., Easton, M., Qian, M., Leary, M., & Brandt, M. (2018). Effect of building direction on porosity and fatigue life of selective laser melted AlSi12Mg alloy. Materials Science and Engineering: A, 729, 76–85. doi:10.1016/j.msea.2018.05.040
7. Lu, X.; Chiumenti, M.; Cervera, M.; Tan, H.; Lin, X.; Wang, S. – Warpage Analysis and Control of Thin-Walled Structures Manufactured by Laser Powder Bed Fusion. – Metals, 2021, 11, 686 https://doi.org/10.3390/met11050686
8. William E. Fraizer, Metal Additive Manufacturing: A review, ASM International 2014
9. Tawaddod Alkindi, Mozah Alyammahi, Rahmat Agung Susantyoko, Saleh Atatreh, The effect of varying specimens’ printing angles to the bed surface on the tensile strength of 3D-printed 17-4PH stainless-steels via FFF additive manufacturing, Springer 2021