Search
Search Results
-
Wind Tunnel Making in Practise
19-24Views:108In this paper, we examined the low speed wind-tunnels. Our goal is to construct an open flow system windtunnel that can be utilized in our measurements. To make such a wind-tunnel we needed to build a prototype and calibrated with the help of measurements. Than we determined the flow at the area of measurement. Finally results of the measurements satisfied our expectations. Although there is still much more in development that we would like to do based on the newly gained experience.
-
Analysis of Smart Photovolatic Systems
67-75Views:102Nowadays more attention should be paid to the electric power generation wi th renewables. The photovoltaic systems have several benefits. But this systems power output could drastically drop by numerous external phenome. To avoid these, we introduce the so called “TIGO” power opti mizing system features and the monitoring of the deployed system on an existing building. We examine the produced energy for a given time period.
-
Wind Energy Harnessing Options at Buildings
51-58Views:103Our goal was to develop a wind turbine system which could be applied in urban areas where the wind power has low potential, such as the cities in the “Alföld” region. The proposed system is able to harness more wind power at lower wind velocity than the commonly used ones, by using advantageo us properties of the flow in tunnels.
-
Numerical Model Analysis of Myring–Savonius wind turbines
180-185Views:177Nowadays the importance of renewable energy is growing, and the utilization of the low wind energy potential is getting crucial. There are turbines with low and high tip speed ratio. Turbines with low tip speed ratio such as the Savonius wind turbine can generate adequate amount of torque at low wind velocities. These types of turbines are also called drag machines. The geometry of the blade can greatly influence the efficiency of the device. With Computational Fluid Dynamics (CFD) method, several optimizations can be done before the production. In our paper the Savonius wind turbine blade geometry was based on the so-called Myring equation. The primary objective of this paper was to increase the power coefficient by modelling the effect of the wind on the turbine blade. For the sake of simplicity, a 2D cross-sectional area was investigated in the simulation with ANSYS CFX 19.1.
-
Calculations of Performance Losses for Automobile Vehicles
210-218Views:214Vehicle-energetic-models are used to analyze the performances and when a comprehensive structure is established even optimization could be done. For these kinds of models, the losses of the vehicles have to be known. These losses could significantly effect of the vehicle fuel consumption. From these losses the rolling resistance, drive elements and aerodynamic drag are discussed. This paper reviews some of the literatures that describes the calculation methods and gives us some idea about the degree of their value. Our further goals are to have an UpToDate loss coefficient dataset and calculation methods for further vehicle-energetic modelling.
-
Numerical Model Analysis of Natural Gas Combustion Burners
67-71Views:142Traditional power plants still the dominating power source for all the major industries and powerdemanding facilities, the most crucial facility for the whole plant operations is the industrial boiler which generatessteam, heating energy or electrical power. Boilers generate energy by combustion. The improvement of combustion efficiency could greatly influence the energy consumption and will make the boiler more efficient and cleaner (less emissions), that’s why it is important to understand the combustion and thermal flow behaviours inside the boiler. Beside experimental testing, computational work nowadays becoming more and more important due to lower cost and acceptable accuracy with minimum error. With numerical calculations method, the computational model created by a Computational Fluid Dynamics (CFD) software could reduce a lot of trial and error on experimental work. In this paper utilizing the ANSYS FLUENT 19.1 software to make crate the combustion model. The ratio of air to fuel mixture, the equivalency factor, mass flow rate of the mixture, velocity, mass fractions of the mixture components (fuel and air) and their temperatures will serve as the input parameter while the exhaust gase component mass fraction, temperature, mass flow and velocity will be monitored.
-
Development of Analysis of Loss Sources of Vehicles
733-737Views:176Vehicle fuel consumption can be significantly influenced by various types of losses such as loss from bearing, aerodynamic drag and rolling drag. It is important to highlight that fuel consumption reduction can be only achieved when those losses are reduced that are induced during the operation.
The aim of our work group is to define the calculation method and the magnitude of the losses of the vehicles. These parameters are intended to be serve as input parameters for future energetic modelling of vehicles.
-
Operational Feasibility Assessment of Geothermal Heat Harnessing Systems
46-53Views:159Renewable energy sources are now essential to establish sustainable development. This paper examines one kind of source the geothermal energy. For geothermal energy when combined with a heat pump COP can be used for evaluation. For solely geothermal sources different approach is needed thus in the paper, a new geothermal heat production coefficient is used to examine the operational feasibility. For the assessment, many hypothetical buildings were created to model their heat demands. Two types of calculation methods are used for heat demand calculation. Based on the results, the maximum depth of a geothermal borehole and economically critical qualitative coefficient was concluded.